PENGARUH DURASI SHOT PEENING TERHADAP STRUKTUR MIKRO DAN KEKERASAN PERMUKAAN PADA AISI 316L

Rizqi ilmal yaqin

Abstract


Stainless steel 316L is widely used in medical applications. AISI 316L has good mechanical properties, good corrosion resistance and easy fabrication. On the other hand, 316L should be upgraded its surface mechanical properties for implantable materials. One of the treatment used is shot peening. shot peening can increase surface hardness in the presence of micro structure changes. These changes are due to plastic deformation and residual stress. This study discusses the effect of shooting time duration of 2, 4, 10, 20, and 30 against the micro structure and surface hardness. The steel balls used are 0.6mm in diameter and 40-50 HRC hardness with 8 bar pressure during shooting. the results of surface hardness on the duration of 2, 4, 10, 20, and 30 minutes obtained respectively are 296.7 HV, 380.8 HV, 425.8 HV, 445.0 HV, 504.9 HV and 523.1 HV. The surface hardness is increased due to structural changes on the surface and sub-surface of the shot peening material. The result of micro structure obtained is that with increasing duration of shot peening and the increasing of hardness value of surface hence grain size at sub surface that is smaller after treatment. Shot peening caused hardness of material 316L stainless steel and made grain of microstructure sub layer.

Keywords


shot peening, Hardness, Structuremicro, AISI 316L

References


Ahmed, A. A., Mhaede, M., Basha, M, Wollmann, M., Wagner, L., 2014, Effect of surface and bulk plastic deformations on the corrosion resistance and corrosion fatigue performance of AISI 316L. Journal Surface & Coatings Technology 259

Xu, S. X.Q.Wu, E.H, Han,W, Katada,Ke, 2008, Effect of oxidation behavior on the corrosion fatigue crack initiation and propagation of 316LN austenitic stainless steel in high temperature water, Mater. Sci. Eng. A 490 16–25.

Arifvianto, B., Suyitno, Mahardika, M., Dewo, P., Iswanto, P. T., Salim, U. A. , 2011, Effect of surface mechanical attrition treatment (SMAT) on microhardness, surface roughness and wettability of AISI 316L. Materials Chemistry and Physics, Vol. 125, 418–426.

Suyitno, dkk .,2012,. Effect of cold working and sandblasting on the microhardness, tensile strength and corrosion resistance of AISI 316L stainless steel . International Journal of Minerals, Metallurgy, and Materials Vol.19 issue 12.

Benedetti, M., Fontanari, B. Winiarski, P.J. Withers, M. Allahkarami, J.C. Hanan., 2015, Fatigue Behavior of Shot Peened Notched Specimens: Effect of The Residual Stress Field Ahead of The Notch Root, Procedia Engineering 109, pp. 80-88, Elsevier.

Zhan, K., Jiang, C. H., Wu, X. Y. and Ji, V., 2012, Surface Layer Characteristics of S30432 Austenite Stainless Steel after Shot Peening, Materials Transactions, Vol. 53, No. 5, pp. 1002-1006, Elsevier.

Azar, V., Hashemi B., Yazdi, Mahboobeh Rezaee. , 2010, The effect of shoot peening on fatigue and corrosion behavior of 316L stainless steel in Ringer’s Solution. Journal Surface & Coatings Technology 204,354-3551.

Liu, Y.G., Li, M.Q., Liu, H.J. ,2017, Nanostructure and surface roughness in the processed surface layer of Ti-6Al-4V via shot peening. Materials Characterization, Vol. 123, pp 83-90.

Umemoto, M., ,2003,, Nanocrystallization of Steels by Severe Plastic Deformation, Materials Transactions, The Japan Institute of Metals, Vol. 44, No.10, pp. 1900-1911.

Liu, Y.G., Li, M.Q., Liu, H.J. ,2017, Nanostructure and surface roughness in the processed surface layer of Ti-6Al-4V via shot peening. Materials Characterization, Vol. 123, pp 83-90.

Jiang, C Q., and Xu, Z., 2014, Residual Stress Relaxation of Shot-Peened Deformation Surface Layer on Duplex Stainless Steel Under Applied Loading, JMEPEG, pp. 408–412, Elsevier

Wibowo, T. N., Iswanto, P. T., Priyambodo, B. H., Amin, N., 2016, Pengaruh Variasi Waktu Shot Peening terhadap Struktur Mikro dan Kekerasan Permukaan Pada Material Implan Aisi 304, Jurnal ROTOR, No.2, pp 70-73.




DOI: http://dx.doi.org/10.28989/senatik.v3i0.120

Article Metrics

Abstract view : 141 times
PDF (Bahasa Indonesia) - 63 times

Refbacks

  • There are currently no refbacks.




Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

Conference SENATIK P-ISSN :2337-3881 and  E-ISSN : 2528-1666